Visonic PowerMax10 Especificações Página 68
- Página / 78
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
D-302756 67
10.
Press the
button.
The PowerMax10-G2 display will read [
FACTORY DEFIN.].
11.
Press the
OKI
button.
The PowerMax10-G2 display reverts to [FACTORY DEFIN.].
OKI
∗ If there are no wireless devices enrolled in the PowerMax10-G2 system, the
PowerMax10-G2 display reads [
NO DEVICES
].
Pressing the or buttons at any stage in the procedure will take
you to “
<OK> TO EXIT
” or pressing the
button at the end of the
procedure will take you to the "
WL DEVICES
" menu.
6 CALLING UPLOAD/DOWNLOAD SERVER
Note:
This option is only used during the installation of panels monitored by compatible Monitoring Stations.
This option allows the installer to initiate a call to the upload/download server. The server uploads the PowerMax10-G2
configuration to its data base and can unload predefined parameters to the PowerMax10-G2.
To Perform Server Upload/Download
1. Make sure the system is disarmed and then press the button
repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".
2.
When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
OKI
The screen will now prompt you to enter your installer code.
3.
Enter your Installer Code.
The PowerMax10-G2 display will read [NEW INSTL CODE].
CODE
4. When the PowerMax10-G2 display reads [NEW INSTL CODE] press the
or
button repeatedly until the PowerMax10-G2 display will read
[START UL/DL].
or
5. When the PowerMax10-G2 display reads [START UL/DL], press the
OKI
button.
OKI
If the UL/DL server telephone number was already defined (see section 4.6.3.2
"Configuring the Event Types to be Reported"), the PowerMax10-G2 display
will read [COMMUNICATING] which is displayed during the dialing process.
If the UL/DL server telephone number was not defined (see section 4.6.3.2
"Configuring the Event Types to be Reported"), the PowerMax10-G2 display
will read [TEL# NOT DEFINED] which is displayed for approx. 30 sec. and is
followed by a sad (failure) tune.
If communication has been established between the PowerMax10-G2 control
panel and the upload/download server, the PowerMax10-G2 display will read
[DOWNLOADING] which is displayed during the dialing process.
If communication has failed between the PowerMax10-G2 control panel and
the upload/download server, the PowerMax10-G2 display will read
[DIAL ATTEMPT FAIL] which is displayed for approx. 30 sec. and is followed
by a sad (failure) tune.
After the downloaded/uploaded process has been completed successfully, the
PowerMax10-G2 display will read [DOWNLOAD OK] which is displayed for
approx. 30 sec. and is followed by a happy (success) tune.
If communication has been established between the PowerMax10-G2 control
panel and the upload/download server but the downloaded/uploaded process
has failed, the PowerMax10-G2 display will read [DOWNLOAD FAILED] which is
displayed for approx. 30 sec. and is followed by a sad (failure) tune.
Pressing the or buttons at any stage in the procedure will take
you to “
<OK> TO EXIT
”.
F
ACTORY DEFIN.
F
ACTORY DEFIN.
D
IAL ATTEMPT FAIL
D
OWNLOADING
D
OWNLOAD FAILED
D
OWNLOAD OK
T
EL# NOT DEFINED
C
OMMUNICATING
S
TART
U
L/DL
N
EW INSTL CODE
E
NTER CODE:
INSTALLER MODE
R
EADY 00:00
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10
(76 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais