Visonic PowerMax10 Especificações Página 66
- Página / 78
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
D-302756 65
you to “
<OK> TO EXIT
” or pressing the
button at the end of the
procedure will take you to the "
LAN
" menu.
The following GSM/ GPRS messages are reported:
Message Description
Unit is OK GSM / GPRS is functioning correctly.
GSM comm. loss The GSM/GPRS module does not communicate with the Panel
Pin code fail Missing or wrong PIN code.
(Only if SIM card PIN code is enabled.)
GSM net. fail Unit failed with registration to local GSM network.
SIM card fail SIM not installed or SIM card failure.
GSM not detected GSM auto enroll failed to detect GSM/GPRS module.
No GPRS service The SIM card does not have the GPRS service enabled.
GPRS conn. fail Local GPRS network is not available or, wrong setting to GPRS APN, user and/or password.
Srvr unavailable IPMP Receiver cannot be reached – Check the Server IP
IP not defined Server IP #1 and #2 are not configured.
APN not defined APN is not configured.
SIM card locked After entering a wrong PIN code 3 consecutive times the SIM is locked. To unlock it enter a PUK
number. The PUK number cannot be entered by the PowerMax10-G2.
Denied by server The IPMP denies the connection request. Check that the Panel is registered to the IPMP Receiver.
5.1.6 LAN Connection Test
The LAN Connection diagnostic procedure tests Broadband Module communication to the IPMP and reports the diagnostic
result. In case of communication failure, detailed information of the failure is reported.
If the Broadband Module is not registered to the PowerMax10-G2, the menu "LAN CONNECT.TEST" will not be displayed.
1. Make sure the system is disarmed and then press the
button
repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".
2.
When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
OKI
The screen will now prompt you to enter your installer code.
3.
Enter your Installer Code.
The PowerMax10-G2 display will read [NEW INSTL CODE].
CODE
4. When the PowerMax10-G2 display reads [NEW INSTL CODE] press the
or
button repeatedly until the PowerMax10-G2 display will read
[DIAGNOSTICS].
or
5. When the PowerMax10-G2 display reads [DIAGNOSTICS], press the
OKI
button.
The PowerMax10-G2 display will read [WL DEVICES].∗
OKI
6. When the PowerMax10-G2 display reads [WL DEVICES], press the or
button repeatedly until the PowerMax10-G2 display will read [LAN].
or
7.
When the PowerMax10-G2 display reads [LAN], press the
OKI
button.**
OKI
8.
The PowerMax10-G2 display will read [PLEASE WAIT…] and will then
automatically change to read [UNIT IS OK].
See the table below for a complete list of possible LAN messages.
∗ If there are no wireless devices enrolled in the PowerMax10-G2 system, the
PowerMax10-G2 display reads [
NO DEVICES
].
** When the
OKI
button is pressed the test result takes between 15 sec. to
4 min. before it is displayed, depending on the severity of the failure.
Pressing the or buttons at any stage in the procedure will take
you to “
<OK> TO EXIT
” or pressing the
button at the end of the
procedure will take you to the "
LAN RESET OPTION
" menu.
U
NIT IS OK
P
LEASE WAIT…
N
EW INSTL CODE
E
NTER CODE:
INSTALLER MODE
R
EADY 00:00
L
AN
W
L DEVICES
D
IAGNOSTICS
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10
(76 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais