Visonic PowerMax10 Especificações Página 62
- Página / 78
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
D-302756 61
The PowerMax10-G2 display will revert to [PSTN UP / DOWN].
30. Press the button.
The PowerMax10-G2 display will read [GPRS UP / DOWN].
31. Press the
OKI
button.
The PowerMax10-G2 display will read [My SIM Tel.#]. Here you enter the
PowerMax10-G2 SIM card telephone number. The Monitoring Station dials this
number when it needs to connect to the PowerMax10-G2 for uploading /
downloading data.
OKI
32. When the PowerMax10-G2 display reads [My SIM Tel.#], press the
OKI
button.
OKI
33.
Enter the SIM card telephone number.
34. Press the
OKI
button twice.
The PowerMax10-G2 display will revert to [My SIM Tel.#].
OKI
OKI
35. Press the
button.
The PowerMax10-G2 display will read [1st caller ID#]. Here you determine
the 1
st
IPMP receiver telephone number. When the PowerMax10-G2 responds
to an incoming call from the telephone number defined here, it creates a
connection to the IPMP for uploading / downloading data.
Note: caller ID#1 / ID#2 should be 6 or more digits for wake-up by IPMP to
work.
36.
When the PowerMax10-G2 display reads [1st caller ID#], press the
OKI
button..
OKI
37.
Enter the first IP receiver telephone number.
38. Press the
OKI
button twice.
The PowerMax10-G2 display will revert to [1st caller ID#].
OKI
OKI
39. Press the
button.
The PowerMax10-G2 display will read [2nd caller ID#]. Here you determine
the 2
nd
IPMP receiver telephone number. When the PowerMax10-G2 responds
to an incoming call from the telephone number defined here, it creates a
connection to that IPMP for uploading / downloading data.
40.
When the PowerMax10-G2 display reads [2nd caller ID#], press the
OKI
button.
OKI
41.
Enter the second IP receiver telephone number.
42. Press the
OKI
button twice.
The PowerMax10-G2 display will revert to [2nd caller ID#].
OKI
OKI
43.
Press the
button.
The PowerMax10-G2 display will revert to [GPRS UP / DOWN].
You can now press the button to take you to the "
RPRT CNFRM ALARM
"
menu (see section 4.6.3.8), or press the button to take you to "
<OK> TO
EXIT
".
5 DIAGNOSTIC TEST
This mode allows you to test the functionality of all devices of the system and to receive / review information regarding the
received signal strength. Communication between system components can also be tested and detailed information is
reported.
The wireless signal strength measured and reported (see details in the drawing below).
IMPORTANT! Reliable reception must be assured during the initial testing and also throughout subsequent system
maintenance. A device should not be installed in location where signal strength is "poor" or "bad". If you get a
"poor"/"bad" signal strength from a certain device, simply re-locate it and re-test until a "good" or "strong" signal strength is
received. This principle should be followed throughout the diagnostic test procedure.
G
PRS UP / DOWN
2
nd caller ID#
2
nd caller ID#
1st caller ID#
1st caller ID#
M
y SIM Tel.#
M
y SIM Tel.#
G
PRS UP / DOWN
P
STN UP / DOWN
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10
(76 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais