Visonic PowerMax10 Especificações Página 65
- Página / 78
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
64 D-302756
[SHOW RF PROBLEMS].
3.
When the PowerMax10-G2 display reads [SHOW RF PROBLEMS], press the
OKI
button.
The PowerMax10-G2 display switches between the average signal strength
indications for the last 24 hours and between the current signal strength
indications of the first RF device type.∗
OKI
4.
Press the
button to view the signal strength indications for the next RF
device type.∗
The signal strength indications are as follows: "
STRONG
";
GOOD
";
POOR
,
BAD
;
"
BAD COM
" (poor communication is detected between the device and the control
panel); "
NO COM
." (no communication); "
NOT TST
" (results are shown without
any performed test); "
NOT NET
" (device is pre-enrolled – not networked);
"
NONE
" (keyfob 24Hr result); or "
EARLY
" (result of the last 24Hrs without
statistics).
∗
Pressing the
OKI
button will display the number and type of device to
which the signal strength indications refer.
Pressing the or buttons at any stage in the procedure will take
you to “
<OK> TO EXIT
”.
5.1.5 GPRS Communication Test
The GPRS Communication diagnostic procedure tests GSM/GPRS communication and reports the diagnostic result. In
case of communication failure, detailed information of the failure is reported.
1. Make sure the system is disarmed and then press the
button
repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".
2.
When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
OKI
The screen will now prompt you to enter your installer code.
3.
Enter your Installer Code.
The PowerMax10-G2 display will read [NEW INSTL CODE].
CODE
4. When the PowerMax10-G2 display reads [NEW INSTL CODE] press the
or
button repeatedly until the PowerMax10-G2 display will read
[DIAGNOSTICS].
or
5. When the PowerMax10-G2 display reads [DIAGNOSTICS], press the
OKI
button.
The PowerMax10-G2 display will read [WL DEVICES].∗
OKI
6. When the PowerMax10-G2 display reads [WL DEVICES], press the
button.
The PowerMax10-G2 display will read [GSM/GPRS]
.
7.
When the PowerMax10-G2 display reads [GSM/GPRS], press the
OKI
button.**
OKI
8.
The PowerMax10-G2 display will read [PLEASE WAIT…] and will then
automatically change to read [UNIT IS OK].
See the table below for a complete list of possible GSM/GPRS messages.
∗ If there are no wireless devices enrolled in the PowerMax10-G2 system, the
PowerMax10-G2 display reads [
NO DEVICES
].
** When the
OKI
button is pressed the test result takes between 15 sec. to
4 min. before it is displayed, depending on the severity of the failure.
Pressing the or buttons at any stage in the procedure will take
U
NIT IS OK
P
LE
A
SE WAIT…
N
EW INSTL CODE
E
NTER CODE:
INSTALLER MODE
R
EADY 00:00
G
SM/GPRS
W
L DEVICES
D
IAGNOSTICS
K
01: NOW: NONE
K
01: 24hr: NONE
Z
01 NOW: NO
T
TST
Z
01: 24hr: GOOD
S
HOW RF PROBLEMS
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10
(76 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.146 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais