Visonic PowerMax10 Especificações Página 37
- Página / 78
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
36 D-302756
19. Press the
OKI
button and enter the third private telephone number
(including area code, if required) of the private subscriber to which the system will
report the event groups defined in Report To Private.
OKI
3
rd
PRVT TEL. NO
20. Press the
OKI
button.
The PowerMax10-G2 display will revert to [3
rd
private tel#].
OKI
21. Press the button.
The PowerMax10-G2 display will read [
4th private tel#].
22. Press the
OKI
button and enter the fourth private telephone number
(including area code, if required) of the private subscriber to which the system will
report the event groups defined in Report To Private.
OKI
4
th
PRVT TEL. NO
23. Press the
OKI
button.
The PowerMax10-G2 display will revert to [4th private tel#].
OKI
24. Press the button.
The PowerMax10-G2 display will read [Redial attempts]. Here you determine
the number of times the communicator will dial the called party’s number
(private telephone).
25.
When the PowerMax10-G2 display reads [Redial attempts], press the
OKI
button.
The PowerMax10-G2 display will read [3 attempts ].
OKI
26. Press the or button repeatedly to select between
"1 attempt", "2 attempts", "3 attempts" and "4 attempts", for example,
"1 attempt".
Attention! A maximum of 2 dialing attempts is permitted by the Australian
Telecommunication Authority.
or
27. Press
OKI
to confirm the selection.
The PowerMax10-G2 display will revert to [Redial attempts].
OKI
28. Press the button.
The PowerMax10-G2 display will read [Tel. acknowledge]. Here you
determine whether the system will use the single acknowledge or the all
acknowledge mode when reporting to private telephones.
Note: In the single acknowledge
mode, receiving an acknowledge signal from
a single telephone is sufficient to consider the current event closed and call off
the communication session. The remaining telephones serve for backup
purposes only. In the all acknowledge
mode, an acknowledge signal must be
received from each telephone before the current event is considered reported.
29.
When the PowerMax10-G2 display reads [Tel. acknowledge], press the
OKI
button.
The PowerMax10-G2 display will read [single ack
].
OKI
30. Press the or button to select between "single ack" and "all
ack", for example, "all ack".
or
31. Press
OKI
to confirm the selection.
The PowerMax10-G2 display will revert to [Tel. acknowledge].
OKI
32. Press the button
33.
The PowerMax10-G2 display will revert to [VOICE REPORT].
T
el. acknowledge
R
edial attempts
V
OICE REPORT
4
th private tel#
4
th private tel#
3
rd private tel#
s
ingle ack
T
el. acknowledge
3
attempts
R
edial attempts
a
ll ack
a
ll ack
1 attempt
1 attempt
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10
(76 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais