Visonic PowerMax10 Especificações Página 23

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 78
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 22
22 D-302756
8. Press
OKI
to confirm.
The PowerMax10-G2 display will revert to [AREA CODE].
OKI
OKI
9. Press the
button.
The PowerMax10-G2 display will read [LINE PREFIX].
10.
Enter the number that is used as a prefix to access an outside telephone line
(if exists).
LINE PREFIX
11. Press
OKI
to confirm.
The PowerMax10-G2 display will revert to [LINE PREFIX].
OKI
12. Press the
button.
The PowerMax10-G2 display will read [DIAL METHOD]. Here you determine
the dialing method used by the automatic dialer built into the PowerMax10-G2
control panel.
13.
When the PowerMax10-G2 display reads [DIAL METHOD], press
OKI
.
The PowerMax10-G2 display will read [
Pulse
].
OKI
14.
Press the
or button to select between "Pulse" and "tone
(dtmf)" for example, "tone (dtmf)"
or
15. Press
OKI
to confirm the selection.
The PowerMax10-G2 display will revert to [DIAL METHOD].
OKI
16. Press the button.
The PowerMax10-G2 display will read [
GSM KEEP ALIVE]. Here you prevent
the GSM Service provider from disconnecting the GSM line if the user has not
initiated any outgoing telephone calls during the last 28 days.
17.
When the PowerMax10-G2 display reads [
GSM KEEP ALIVE], press
OKI
.
The PowerMax10-G2 display will read [
disable
].
OKI
18.
Press the
or button to select between "disable" and
"every 28 days", for example, "every 28 days".
or
19. Press
OKI
to confirm the selection.
The PowerMax10-G2 display will revert to [
GSM KEEP ALIVE].
OKI
You can now press the button to revert to the "
AREA CODE
" menu, or
press the button to take you to "
<OK> TO EXIT
".
4.6.2.2 Configuring GPRS / BB Communicators
The GSM/GPRS module is capable of communicating with the Monitoring station receiver by GPRS, GSM Voice and SMS
Channels. Each of the channels can be separately enabled or disabled in order to allow or prohibit the module from using it
for the event reporting. If all channels are enabled, the GSM/GPRS module will always try GPRS first. If fails, it will try GSM
voice. If fails, it will try any other possible method (PSTN Broadband) and only then it will try SMS. This is due to the fact
that SMS the most unreliable option of communication. Disabling any of the GSM Module channels will cause the module
to use a different sequence than the one described above.
20. Make sure the system is disarmed and then press the
button
repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".
21.
When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
OKI
G
SM KEEP ALIVE
D
IAL METHOD
INSTALLER MODE
R
EADY 00:00
disable
e
very 28 days
e
very 28 days
GSM KEEP ALIVE
Pulse
t
one
(
dtmf)
t
one (dtmf)
L
INE PREFIX
A
REA CODE
D
IAL METHOD
L
INE PREFIX
Vista de página 22
1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 77 78

Comentários a estes Manuais

Sem comentários