Visonic PowerMax10 Especificações descarregar pdf (Página 13)

12 D-302756

The PowerMax10-G2 display reverts to "

23:DURESS

" and a "Happy Tune" ☺

sounds.

You can now press the or button to program any other menu in

DEFINE PANEL

" or press the button to take you to "

<OK> TO EXIT



☺

4.4 Zones / Devices

4.4.1 General Guidance

The ZONES / DEVICES mode enables the following functions:

- Defining default parameters common for each devices family.

- Adding new devices (enrolling) and defining their zones name, zone type and chime zone.

- Deleting devices.

- Modifying devices parameters.

- Reviewing devices parameters.

Enrolling can be performed for Keyfobs (multi-button), wireless detectors, wireless sirens and repeaters.

The control panel enables entering a device identification (ID) instead of enrolling an actual device. This enables pre-enrolling off

site.

Upon boot up, the control panel checks if there are pre-enrolled devices that have not yet been registered (ID of the devices are

entered but the devices have not communicated with the control panel). In this case, the control panel will display "SYNC WITH

DEV" on the LCD and the trouble LED will be on until all the devices have registered or the pre-enrolled devices that have not

registered will be deleted from the enrollment menu.

Refer to sections 4.4.3 and 4.4.4 for detailed instructions on Enrolling/Deleting a device.

Notes

- Keyfob enrolling can be performed also by the user (via USER SETTINGS menu).

- Wired magnetic contact or any other contact can be enrolled in zones 29 & 30.

- Wireless detectors can be enrolled in zones 01-28.

Before beginning, gather all the devices that you intend to enroll and make sure they all have batteries installed.

Your control panel must recognize the unique identification code (ID) of each such detector in order to supervise them,

receive their signals and respond accordingly.

• Before enrolling, the lens at the front of PIR and dual-technology sensors should be masked to prevent inadvertent

transmission.

• Make sure that magnetic contact transmitters are together with their magnets, to prevent them from sending out alarm

transmissions.

4.4.2 Adding a Wireless Device

This section describes how to add a new device to the PowerMax10-G2 control panel.

Note: It is much easier to enroll the device while holding the device in your hand, close to the control panel.

A. To Add a Device

1. Make sure the system is disarmed and then press the button

repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".

When the PowerMax10-G2 display reads [INSTALLER MODE], press

OKI

The screen will now prompt you to enter your installer code.

Enter your Installer Code.

The PowerMax10-G2 display will read [NEW INSTL CODE].

CODE

4. Press the button and select the [ZONES/DEVICES] option.

5. When the PowerMax10-G2 display reads [ZONES/DEVICES] press

OKI

The PowerMax10-G2 display will read [ADD NEW DEVICES].

6. Press

OKI

. You are now instructed to enroll the device.

OKI

Enter the 7-digit number printed on the back side of the device and press

OKI

Perform the enrollment sequence for the specific device:

For most devices: Remove the device bracket or cover and press the device's



OKI

23:DURESS

EW IN

TL CODE

NTER ID No

NROLL NOW or

NTER CODE: 

INSTALLER M

EADY 00:00

DD NEW

EVICES

ONES/DEVICES

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 77 78

Comentários a estes Manuais

Sem comentários

Visonic PowerMax10 Especificações Página 13

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10