Visonic PowerMax10 Especificações descarregar pdf (Página 14)

D-302756 13

Enroll button continuously until the red & green LEDs turn ON and then release.

The PowerMax10-G2 will indicate the result on its LCD display.

For Keyfobs: Press the '*' button until the red LED blinks rapidly and then release

(the LED will continue blinking) then press the same button again. The LED lights

green and the PowerMax10-G2 will indicate the result on its LCD display.

The PowerMax10-G2 display reads [

DEVICE ENROLLED

] (or [

ID accepted

] if

the device was enrolled manually by entering the ID number), a "Happy Tune" ☺

sounds and the PowerMax10-G2 display will then change to [

K01:Keyfob /

Z01:Motion Sens / S01:Siren

depending on the type of enrolled device].

However, if the device was previously enrolled in the system, the PowerMax10-

G2 display reads [

ALREADY ENROLLED

Repeat the above procedure for each device to be enrolled in the PowerMax10-

G2 system.

Continue to section 4.4.2.1 Assigning a Location, Zone Type and Chime Option.

When exiting "

ZONES / DEVICES

" menu the PowerMax10-G2 system displays the

number of devices that need to be updated, as follows: DEV UPDATING NNN.

* If you enter the 7-digit number, you must physically install the device to

complete the procedure. If the device is not installed, the system will display

the device as "

NOT NET

" (device is pre-enrolled – not networked).

You can now press the button to enroll the next device of the same type or

press the

OKI

button to move to the "

LOCATION

" menu (see section 4.4.2.1) or

press the button to take you to "

<OK> TO EXIT



☺

……..

4.4.2.1 Assigning a Location, Zone type and Chime Option

B. To Assign a Location, Zone Type and Chime Option

The PowerMax10-G2 system behavior is defined according to one of 15 zone types assigned to each of the system's 30

(wireless & wired) zones.

Note: This step is applicable to detectors only.

Continue below from the previous section.

1. Press

OKI

. The PowerMax10-G2 display will read [Z01: LOCATION].

When the PowerMax10-G2 display reads [LOCATION], press

OKI

The PowerMax10-G2 display will read [Front door].

Press the

or button repeatedly to select a location, or, enter the

location number, for example, "Master Bdrm".

4. Press

OKI

to confirm. The PowerMax10-G2 display will read [Z01:ZONE

TYPE].

OKI

5. When the PowerMax10-G2 display reads [Z01: ZONE TYPE], press

OKI

The PowerMax10-G2 display will read [12.Non-Alarm].

OKI

Press the

or button repeatedly to select a zone type, or, enter

the zone type number, for example, pressing 03 selects "3. Home Delay".

To understand the behavior of each zone, see section 4.4.2.3 Zone Types.

OKI

Press

OKI

to confirm. The PowerMax10-G2 display will read [SET CHIME].

Press

OKI

to change chime settings or press the button to skip.

After pressing

OKI

, the PowerMax10-G2 display will read [chime OFF ].

OKI

Press the

and buttons to select between "CHIME OFF" and

"melody-chime".

hime off 

01: SET CHIME

12.Non

larm

e Delay

aster Bdrm

01:ZONE TYPE

ront door

01: LOCATION

LREADY ENROLLED

01:Siren

01:Motion Sens

01:Keyfob

EVICE ENROLLED

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 77 78

Comentários a estes Manuais

Sem comentários

Visonic PowerMax10 Especificações Página 14

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10