Visonic PowerMax10 Especificações Página 64
- Página / 78
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
D-302756 63
The first device type is displayed, "CONTACT SENSORS".
OKI
4.
Press the
or button repeatedly to select between "CONTACT
SENSORS", "MOTION SENSORS", "SMOKE SENSORS", "KEYFOBS", "SIRENS" or
"REPEATERS", for example, "MOTION SENSORS".
or
5.
After making your selection, press the
OKI
button.
The PowerMax10-G2 display will read the device name alternating with the
location.
OKI
6.
Press the
OKI
button. The PowerMax10-G2 display will read [TESTING Zxx
001] or [ACTIVATE NOW Uxx] for keyfobs.
OKI
After testing the PowerMax10-G2 display will then automatically change to read
the average level for the last 24 hours (for stationary devices) or the number of
activations that the control panel has received (for keyfobs).
The signal strength indications are as follows: "
STRONG
";
GOOD
"; "
POOR
";
"
BAD
"; "
BAD COM
" (poor communication is detected between the device and the
control panel); "
NO COM
." (no communication); "
NOT TST
" (results are shown
without any performed test); "
NOT NET
" (device is pre-enrolled – not
networked); "
NONE
" (keyfob 24Hr result); or "
EARLY
" (result of the last 24Hrs
without statistics).
Pressing the or buttons at any stage in the procedure will take
you to “
<OK> TO EXIT
”.
or
5.1.3 Displaying Signal Strength Indication of All Devices
1.
Repeat steps 1 to 6 from section 5.1.1 Testing all Devices.
2.
When the PowerMax10-G2 display reads [TEST ALL DEVICES], press the
and buttons repeatedly until the PowerMax10-G2 display will
read [SHOW ALL DEVICES].
or
3.
When the PowerMax10-G2 display reads [SHOW ALL DEVICES], press the
OKI
button.
The PowerMax10-G2 display switches between the average signal strength
indication for the last 24 hours and between the current signal strength
indications of the first device type.∗
OKI
4.
Press the
button to view the signal strength indications for the next
device type.∗
The signal strength indications are as follows: "
STRONG
";
GOOD
"; "
POOR
"; "
BAD
";
"
BAD COM
" (poor communication is detected between the device and the control
panel); "
NO COM
." (no communication); "
NOT TST
" (results are shown without
any performed test); "
NOT NET
" (device is pre-enrolled – not networked);
"
NONE
" (keyfob 24Hr result); or "
EARLY
" (result of the last 24Hrs without
statistics).
∗
Pressing the
OKI
button will display the number and type of device to
which the signal strength indications refer.
Pressing the or buttons at any stage in the procedure will take
you to “
<OK> TO EXIT
”.
5.1.4 Displaying Signal Strength Indication of RF Devices
1.
Repeat steps 1 to 6 from section 5.1.1 Testing all Devices.
2.
When the PowerMax10-G2 display reads [TEST ALL DEVICES], press the
or button repeatedly until the PowerMax10-G2 display will read
or
T
EST ALL DEVICES
K
01: NOW: NONE
K
01: 24hr: N
O
NE
Z
01 NOW: NOT TST
Z
01: 24hr: GOOD
T
EST ALL DEVICES
S
HOW ALL DEVICES
M
OTION SENSORS
C
ONTACT SENSORS
A
CTIVATE NOW Uxx
Z
01 24Hr: EARLY
Z
01 NOW: STRONG
T
ESTING Zxx 001
F
ront door
Z
xx:Motion Sens
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10
(76 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais