Visonic PowerMax10 Especificações descarregar pdf (Página 11)

10 D-302756

The PowerMax10-G2 display reads [

NEW MASTER CODE

] and a "Happy Tune" ☺

sounds to confirm the new MASTER INSTALLER code.

You can now press the button to set the INSTALLER code or press the

button to take you to "

<OK> TO EXIT



☺

Note: Master Installer Code should never be programmed as “0000”. Doing so will lock the user out of the installer menu!

4.3.3 Setting User Codes

For detailed instructions on setting user codes, refer to the PowerMax10-G2 user guide "Menus and Functions".

4.3.4 Enabling User Permit for Installer Access

User Permission enables you to determine whether access to the INSTALLER MODE requires user permission. Access to

the installer menu, in PowerMax10-G2 that has "User Permission" enabled (for example, in UK) is via the last menu in the

user menu. This option can be changed, if necessary. Here you determine whether the access to the INSTALLER MODE

requires user permission. If you select ENABLE, the installer mode will be accessible only through the user menu after

entering the user code.

Options: Enable (default in UK), Disable (default).

Note: To comply with EN requirements, "Enable" must be selected.

To Enable User Permit for Installer Access

1. Make sure the system is disarmed and then press the button

repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".

When the PowerMax10-G2 display reads [INSTALLER MODE], press

OKI

The screen will now prompt you to enter your installer code.

OKI

Enter your Installer Code.

CODE

4. Press the or button repeatedly and select the [DEFINE PANEL]

option.

5. When the PowerMax10-G2 display reads [DEFINE PANEL], press

OKI

The PowerMax10-G2 display will read [01:ENTRY DELAY 1].

OKI

When the PowerMax10-G2 display reads [01:ENTRY DELAY 1], press

the

or button repeatedly until the display will read [36:USER

PERMIT].

Press

OKI

and select between "Disable" (default) and "Enable" and then

press

OKI

to confirm.

OKI

The PowerMax10-G2 display reverts to "

36:USER PERMIT

" and a "Happy Tune"

☺ sounds.

You can now press the or button to program any other menu in

DEFINE PANEL

" or press the button to take you to "

<OK> TO EXIT



☺

4.3.5 Configuring Permissions for System Reset after Alarm Event

(Not applicable in the USA)

Here you determine whether the system can be rearmed (after an event) by the user or only by the installer.

Options: user reset (default), engineer reset, or anti code reset.

If Engineer Reset is selected, the system can be rearmed only by the installer; by entering and exiting the installer menu, by

entering and exiting the event log (see section 8), or by remote telephone. To perform Engineer Reset via the telephone,

establish communication with the PowerMax10-G2 (see user guide, Chapter 5) and continue as follows:

a.  [*], [installer code], [#]

b. Wait for 2 beeps

c.  [*], [1], [#]

d.  [*], [99], [#]

Visonic uses Technistore anti code reset. Installers should check with their Monitoring Station for a code version (seed

code) which needs to be entered.

36:USER PERMIT

6:USER PERMIT

1:ENTRY DELAY 1

NTER CODE: 

INSTALLER MODE

EADY 00:00

EFINE PANEL

NEW MASTER CODE

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 77 78

Comentários a estes Manuais

Sem comentários

Visonic PowerMax10 Especificações Página 11

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10