Visonic PowerMax10 Especificações Página 38
- Página / 78
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
D-302756 37
You can now press the button to take you to the "
SMS REPORT TEL#
"
menu (see the next section), or press the button to take you to "
<OK>
TO EXIT
".
D. To Configure Reports to User by SMS
34. When the PowerMax10-G2 display reads [VOICE REPORT], press the
button.
The PowerMax10-G2 display will read [SMS REPORT TEL#].
35.
When the PowerMax10-G2 display reads [SMS REPORT TEL#], press the
OKI
button.
The PowerMax10-G2 display will read [1st SMS tel#].
OKI
36. Press the
OKI
button and enter the first SMS phone number (including
area code, 16 digits maximum) to which pre-selected event types will be
reported.
OKI
1
st
SMS TEL. NO
37. Press the
OKI
button.
The PowerMax10-G2 display will revert to [1st SMS tel#].
OKI
38. Press the button.
The PowerMax10-G2 display will read [2nd SMS tel#].
39. Press the
OKI
button and enter the second SMS phone number (including
area code, 16 digits maximum) to which pre-selected event types will be
reported.
OKI
2
nd
SMS TEL. NO
40. Press the
OKI
button.
The PowerMax10-G2 display will revert to [2nd SMS tel#].
OKI
41. Press the button.
The PowerMax10-G2 display will read [3rd SMS tel#].
42. Press the
OKI
button and enter the third SMS phone number (including
area code, 16 digits maximum) to which pre-selected event types will be
reported.
OKI
3
rd
SMS TEL. NO
43. Press the
OKI
button.
The PowerMax10-G2 display will revert to [3
rd
SMS tel#].
OKI
44. Press the button.
The PowerMax10-G2 display will read [4
th
SMS tel#].
45. Press the
OKI
button and enter the fourth SMS phone number (including
area code, 16 digits maximum) to which pre-selected event types will be
reported.
OKI
4
th
SMS TEL. NO
46. Press the
OKI
button.
The PowerMax10-G2 display will revert to [4
th
SMS tel#].
OKI
You can now press the button to take you to the "
1st private tel#
"
menu (see step C. To Configure Event Types to be Reported to User), or
press the button to take you to "
<OK> TO EXIT
".
4.7 Security System Configuration
4.7.1 Enable Cross Zoning
Here you determine whether cross zoning will be active or inactive. Cross zoning is a method used to counteract false
alarms - an alarm will not be initiated unless two adjacent zones are violated within a 30-second time limit.
This feature is active only when arming AWAY and only with zone couples from zone No. 18 to 27
(18 and 19, 20 and 21,
etc.). You may use any one of these zone couples to create a “cross-zoned” area.
Note: If one of two crossed zones is bypassed (see Para. 4.3.5), the remaining zone will function independently.
4
TH SMS tel#
4
th SMS tel#
3
rd SMS tel#
3
rd SMS tel#
2
nd SMS tel#
2
nd SMS tel#
1st SMS tel#
1st SMS tel#
S
MS REPORT TEL#
Cross Zoning
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10
(76 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais