Visonic POWERMASTER-10 Guia do Utilizador descarregar pdf (Página 73)

4 D-304271 PowerMaster-10/30 G2 Addendum

07:RPT CNFM ALRM

Define whether the system will report a confirmed alarm.

enable + bypass (default) - The system will report a confirmed alarm and will bypass all

alarmed open zones when the siren ends or when the confirmation timer expires.

disable - The system will not report a confirmed alarm.

enable - The system will report a confirmed alarm.

08:ENTRY DELAY 1

09:ENTRY DELAY 2

Two different entry delays allow the user to enter the protected site (while the system is in the

armed state) via 2 specific doors and routes without causing an alarm.

Following entry, the user must disarm the control panel before the entry delay expires. Slow-

rate warning beeps start sounding once the door is opened, until the last 10 seconds of the

delay, during which the beeping rate increases. Locations No. 1 (entry delay 1) and 2 (entry

delay 2) allow you to program the length of these delays.

Options: 10/15/30 (ENTRY DELAY 1 default)/45/60 (ENTRY DELAY 2 default) seconds;

3/4 minutes

DD243 Setup

13:OPERATION MOD

⋅ ⋅ ⋅

03:DD243 SETUP

Enter the "03:DD243 SETUP" menu, and press to configure DD243 compliance standard settings.

Option Configuration Instructions

01:DISARM OPTION

Define when it is possible to disarm the system:

entry/wl+awy kp – By the control panel when the system is armed AWAY. By keyfob or

keyprox during entry delay only.

entry/all devs - During entry delay, when the system is armed AWAY, by all devices. When

not in entry delay by keyfob or keyprox only.

entry/DD devs (default) - During entry delay, when the system is armed AWAY, by using the

keyfob or keyprox. Keypads cannot disarm at all.

anytime/all dev – At any time and by all devices.

02:ENTRY ALARM

Define whether the system will report a confirmed alarm during an entry delay (see CONFIRM

ALARM below).

DD243 (default) - An alarm initiated by another detector during the entry delay is not regarded

as a confirmed alarm.

EN standard - The control panel will report a confirmed alarm for the second alarm that is

triggered from a different zone within the confirmation time. There are no alarm restrictions

during entry delay or for the delay zone.

03:END EXIT MODE

Define how the exit delay is terminated or restarted according to the following options:

door/fob only - When the door is closed, or by pressing the AUX button on the keyfob

whichever first.

restart>reentry - Exit delay restarts when the door is reopened during exit delay. The restart

occurs once only. Restarting the exit delay is helpful if the user re-enters immediately after

going out to retrieve an item that was left behind.

door/fob/timer - When the door is closed, by pressing the AUX button on the keyfob

, or when

the exit delay has expired, whichever first.

fob/timer (default) - By pressing the AUX button on the keyfob

, or when the exit delay has

expired, whichever first.

04:FOB/KP PANIC

Define the devices that cannot trigger a panic alarm.

DD243 – MCT-234.

all - All devices can trigger a panic alarm

Applies only when the keyfob is defined as "skip exit delay" (for further details, see the keyfob's User's Guide)

1 2 ... 68 69 70 71 72 73 74 75 76

Comentários a estes Manuais

Sem comentários

Visonic POWERMASTER-10 Guia do Utilizador Página 73

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic POWERMASTER-10