Visonic POWERMASTER-10 Guia do Utilizador Página 72
- Página / 96
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
7. MAINTENANCE
72
D-304762 PowerMaster-10/30 G2 Installer's Guide
Fault What it means Solution
4. Enroll the device again.
RSSI LOW The GSM communicator has detected that
GSM network signal is weak
Move the Panel and GSM unit to another
location.
SIREN AC
FAILURE
There is no power to the siren Make sure that the AC power supply is
connected properly
TAMPER OPEN The sensor has an open tamper Close sensor tamper
TROUBLE
The sensor reports trouble Replace the sensor
SOAK TEST FAIL
1
Detector alarms when in Soak Test mode If you wish to continue the Soak Test, no
further action should be taken.
If you wish to abort the Soak Test, disable the
Soak Test (see section 5.4.7).
7.2 Dismounting the Control Panel
A. Remove the screw that fastens the front unit to the back unit, see Figure 3.1 (PowerMaster-10 G2) / 4.1
(PowerMaster-30 G2).
B. Remove the 4 screws that fasten the back unit to the mounting surface - see Figure 3.1 (PowerMaster-10 G2) / 4.1
(PowerMaster-30 G2) - and remove the control panel.
7.3 Replacing the Backup Battery
Replacement and first-time insertion of battery pack is similar, see Figure 3.8 (PowerMaster-10 G2) /
4.10 (PowerMaster-30 G2).
With a fresh battery pack, correct insertion and tightened battery compartment lid, the TROUBLE indicator should
extinguish. However, the “MEMORY” message will now blink in the display (caused by the “tamper” alarm you triggered
when opening the battery compartment lid). Clear it by arming the system and immediately disarming.
7.4 Fuse Replacement
The PowerMaster-10 G2 has an internal fuse (the PowerMaster-30 G2 has two internal fuses) that has automatic reset.
Therefore, there is no need to replace the fuse(s).
When over current condition occurs, the fuse cuts off the circuit current. Upon fault current being removed for several
seconds, the fuse is automatically reset and allows current flow through the circuit again.
7.5 Replacing/Relocating Detectors
Whenever maintenance work involves replacement or re-location of detectors, always perform a full diagnostic test
according to section 5.9.
Remember! A "poor" signal is not acceptable.
7.6 Annual System Check
Note: The PowerMaster system must be checked by a qualified technician at least once every three (3) years
(preferably every year).
The annual system check is designed to ensure proper operation of the alarm system by performing the following checks:
•
Periodic test
•
Arm/disarm function
•
No trouble messages are displayed on control panel
•
The clock displays the correct time
•
Reporting: generating an event to be transmitted to the Monitoring Station and to the user.
1
Soak Test is not applicable for UL installations
- PowerMaster-10/30 G2 1
- Version 17 1
- 1. INTRODUCTION 3
- Figure 3.2 –Phone Wiring 9
- 3.4 GSM Module Installation 10
- 3.5 PGM-5 Installation 11
- Figure 3.6a – Cable Wiring 12
- UL listed 13
- PGM: not to be enabled in UL 13
- Figure 3.7a - Power Cable 14
- Connection 14
- Figure 3.9 - Final Closure 16
- Figure 4.3a – Phone Wiring 18
- 4.6 GSM Module Installation 20
- 4.8 PGM-5 Installation 21
- Figure 4.9a –Expander Module 22
- Figure 4.9b – Zone 23
- and Siren Wiring 23
- 4.11 Battery Insertion 25
- Figure 4.13 26
- 5. PROGRAMMING 27
- [1] in Step 1 above) 28
- 5.2.2 Selecting options 28
- – Exiting the Installer Mode 29
- – Setting Installer Codes 29
- 5.4 Zones / Devices 30
- Part B - Configuration 31
- - Configuring New Devices 32
- 5.4.3 Deleting a Device 34
- 5.4.5 Replacing a Device 34
- – Replacing a Device 35
- – Changing Defaults 35
- 5.5 Control Panel 36
- 01:ENTRY DELAY1 37
- 02:ENTRY DELAY2 37
- VOICE REPORT 38
- SMS REPORT 38
- 09:ARMING KEY 39
- 21:SWINGER STOP 39
- 22:CROSS ZONING 39
- 38:CANCEL ALARM 41
- 39:ALARM RESET 41
- 40:ABORT FIRE T 41
- 43:PANEL SIREN 41
- 44:SIREN TIME 41
- 5.6 Communication 44
- PowerMaster String Editor 48
- Event Reporting Chart 51
- IMAGE FORWARD 52
- 1st e-mail 52
- 2nd e-mail 52
- 5.6.8 Broadband 54
- 5.7 PGM Output 55
- 5.8 Custom Names 56
- 5.8.2 Record Speech 57
- 5.8.3 Voice Box Mode 57
- 5.9.4 Testing the SIM Number 60
- 5.10 User Settings 61
- 5.11 Factory Default 61
- 5.12 Serial Number 61
- 5.13 Start UL/DL 62
- 5.14 Partitioning 62
- 5.15 Operation Mode 62
- 5.15.2 Select setting 63
- 5.15.3 BS8243 Setup 63
- 5.15.4 DD243 Setup 64
- 5.15.5 CP01 Setup 66
- 5.15.6 OTHERS Setup 67
- 6. PERIODIC TEST 68
- 7. MAINTENANCE 70
- 7.4 Fuse Replacement 72
- 7.6 Annual System Check 72
- 8. READING THE EVENT LOG 73
- APPENDIX A. Specifications 74
- A2. Wireless 75
- A3. Electrical 75
- A4. Communication 76
- A5. Physical Properties 77
- B2. Common Areas 78
- Assignments 79
- C2. Keyfob Transmitter List 80
- APPENDIX D. Event Codes 82
- Type Number Range 83
- APPENDIX E. Sabbath Mode 84
- F1. Getting Started 85
- F2. Specifications 85
- F3. Installation 86
- Hardware Installation 87
- Control Panel Configuration 89
- APPENDIX G. Glossary 90
- Compliance with 92
- Standards 92
- WARRANTY 93
- Initiating Alarms 95
- Preparing to Arm 95
- Zone Bypass Scheme 96
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic POWERMASTER-10
(27 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais