Visonic POWERMASTER-10 Guia do Utilizador Página 46
- Página / 96
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5. PROGRAMMING
46
D-304762 PowerMaster-10/30 G2 Installer's Guide
Step 1
Step 2
Step 3 Step 4
Select "COMMUNICATION" Select Communication
Sub-menu option
Select the "Communication" Parameter you wish to configure
See
→
→→
→
3rd private tel #
→
→→
→
3rd SMS tel #
Guide
Chapter
6
Section
C.11
→
→→
→
4th private tel #
→
→→
→
4th SMS tel #
→
→→
→
Redial attempts
→
→→
→
Voice<-->private
→
→→
→
Tel. acknowledge
5:MOTION CAMERA
IMAGE FORWARD
VIEW ON DEMAND
5.6.6
→
→→
→
1st e-mail
VIEW TIME WINDOW
→
→→
→
2nd e-mail
VIEW OTHER ALARM
→
→→
→
3rd e-mail
→
→→
→
4th e-mail
→
→→
→
1st MMS tel #
→
→→
→
2nd MMS tel #
→
→→
→
3rd MMS tel #
→
→→
→
4th MMS tel #
6:UP/DOWNLOAD
PSTN UP/DOWNLOAD
GPRS UP/DOWNLOAD
5.6.7
→
→→
→
Remote access
→
→→
→
Panel SIM Tel #
→
→→
→
Mast. UL/DL code
→
→→
→
1st caller ID#
→
→→
→
Inst. UL/DL code
→
→→
→
2nd caller ID#
→
→→
→
UL/DL Modes
→
→→
→
Up/Download tel#
7:BROADBAND
1,
2
DHCP Client RESET MODULE
5.6.8
MANUAL IP
→
→→
→
IP ADDRESS
→
→→
→
SUBNET MASK
→
→→
→
DEFAULT GW
5.6.2 Configuring PSTN (landline phone) Connection
The PowerMaster panels include a telephone dialer for reporting to Monitoring Stations using several optional Alarm
Formats (see section 5.6.4 option 41) and to Private Telephones (see section 5.6.5 "
VOICE REPORT
"). Here you
configure necessary parameters related to the PSTN telephone line to which the PowerMaster is connected.
04:COMMUNICATION
⋅ ⋅ ⋅
1:PSTN TEL LINE
⋅ ⋅ ⋅
MENU you wish
Enter "1:PSTN TEL LINE", select the menu you wish to configure (see guidance above and in section 5.6.1), then refer
to the table below.
Option Configuration Instructions
AREA CODE SKIP
In some older PSTN networks, it may not be possible to dial from the control panel to other
PSTN telephone numbers (such as monitoring stations or private phones), if the dialed
number contains an area code which is identical to the area code of the panel (i.e. both the
panel and the other numbers are in the same PSTN area code).
If you encounter the same problem with the PSTN network the panel is connected to, you
must enter here the area code of the PSTN telephone line to which the panel is connected (up
to 4 digits) so that when dialing to other PSTN phone numbers programmed with the same
area code, the PowerMaster will skip the area code from the dialed number.
LINE PREFIX
Enter the prefix digit (if necessary) for the system to access an outside telephone line.
DIAL METHOD
Define the dialing method used by the PSTN dialer of the PowerMaster control panel.
Options: pulse and tone (dtmf) (default).
1
Broadband is not applicable for UL installations
2
The name of the product is PowerLink3 IP Communicator
- PowerMaster-10/30 G2 1
- Version 17 1
- 1. INTRODUCTION 3
- Figure 3.2 –Phone Wiring 9
- 3.4 GSM Module Installation 10
- 3.5 PGM-5 Installation 11
- Figure 3.6a – Cable Wiring 12
- UL listed 13
- PGM: not to be enabled in UL 13
- Figure 3.7a - Power Cable 14
- Connection 14
- Figure 3.9 - Final Closure 16
- Figure 4.3a – Phone Wiring 18
- 4.6 GSM Module Installation 20
- 4.8 PGM-5 Installation 21
- Figure 4.9a –Expander Module 22
- Figure 4.9b – Zone 23
- and Siren Wiring 23
- 4.11 Battery Insertion 25
- Figure 4.13 26
- 5. PROGRAMMING 27
- [1] in Step 1 above) 28
- 5.2.2 Selecting options 28
- – Exiting the Installer Mode 29
- – Setting Installer Codes 29
- 5.4 Zones / Devices 30
- Part B - Configuration 31
- - Configuring New Devices 32
- 5.4.3 Deleting a Device 34
- 5.4.5 Replacing a Device 34
- – Replacing a Device 35
- – Changing Defaults 35
- 5.5 Control Panel 36
- 01:ENTRY DELAY1 37
- 02:ENTRY DELAY2 37
- VOICE REPORT 38
- SMS REPORT 38
- 09:ARMING KEY 39
- 21:SWINGER STOP 39
- 22:CROSS ZONING 39
- 38:CANCEL ALARM 41
- 39:ALARM RESET 41
- 40:ABORT FIRE T 41
- 43:PANEL SIREN 41
- 44:SIREN TIME 41
- 5.6 Communication 44
- PowerMaster String Editor 48
- Event Reporting Chart 51
- IMAGE FORWARD 52
- 1st e-mail 52
- 2nd e-mail 52
- 5.6.8 Broadband 54
- 5.7 PGM Output 55
- 5.8 Custom Names 56
- 5.8.2 Record Speech 57
- 5.8.3 Voice Box Mode 57
- 5.9.4 Testing the SIM Number 60
- 5.10 User Settings 61
- 5.11 Factory Default 61
- 5.12 Serial Number 61
- 5.13 Start UL/DL 62
- 5.14 Partitioning 62
- 5.15 Operation Mode 62
- 5.15.2 Select setting 63
- 5.15.3 BS8243 Setup 63
- 5.15.4 DD243 Setup 64
- 5.15.5 CP01 Setup 66
- 5.15.6 OTHERS Setup 67
- 6. PERIODIC TEST 68
- 7. MAINTENANCE 70
- 7.4 Fuse Replacement 72
- 7.6 Annual System Check 72
- 8. READING THE EVENT LOG 73
- APPENDIX A. Specifications 74
- A2. Wireless 75
- A3. Electrical 75
- A4. Communication 76
- A5. Physical Properties 77
- B2. Common Areas 78
- Assignments 79
- C2. Keyfob Transmitter List 80
- APPENDIX D. Event Codes 82
- Type Number Range 83
- APPENDIX E. Sabbath Mode 84
- F1. Getting Started 85
- F2. Specifications 85
- F3. Installation 86
- Hardware Installation 87
- Control Panel Configuration 89
- APPENDIX G. Glossary 90
- Compliance with 92
- Standards 92
- WARRANTY 93
- Initiating Alarms 95
- Preparing to Arm 95
- Zone Bypass Scheme 96
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic POWERMASTER-10
(27 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais