Visonic POWERMASTER-10 Guia do Utilizador Página 58
- Página / 96
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5. PROGRAMMING
58
D-304762 PowerMaster-10/30 G2 Installer's Guide
5.9 Diagnostics
5.9.1 General Guidance – "Diagnostics" Flow-Chart & Menu Options
The DIAGNOSTICS menu enables you to test your system and to verify proper operation of your PowerMaster panel,
wireless devices attached to it and the communication (GSM/GPRS/SIM) modules.
IMPORTANT! Reliable reception must be assured during the initial testing and also throughout subsequent system
maintenance. A device should not be installed in location where signal strength is "poor". If you get "poor" signal
strength from a certain device, simply re-locate it and re-test until a "good" or "strong" signal strength is received. This
principle should be followed throughout the diagnostic test procedure.
Note: For UL installations, "strong" signal strength for WL devices is required.
The diagnostic test process is shown below.
The "07.DIAGNOSTICS" menu contains several sub-menu options, each covering a group of configurable features and
parameters related to the communication and reporting as follows (see the list in Step 3 of the chart below):
Option Description of Option Features and Parameters Section
WL DEVICES
Describes how to test the devices attached to the PowerMaster panel, review
devices' status and RF signal status. You can test all devices, test single device,
review devices status and review RF problems, in case of any.
5.9.2
GSM/GPRS
Describes how to test the GSM/GPRS communication module.
5.9.3
SIM NUMBER TEST
1
Tests the SIM number to ensure correct entry of the SIM number in the control
panel.
5.9.4
BROADBAND
MODULE
2, 3
Contains DHCP Client settings, enables to enter LAN parameters and reset
broadband module/settings.
5.9.5
To enter the "07.DIAGNOSTICS" menu and to select and configure an option, proceed as follows:
Step 1
Step 2
Step 3 Step 4
Select
"07.DIAGNOSTICS
"
Select sub-menu option Select the diagnostics you want to perform
See
INSTALLER MODE
07.DIAGNOSTICS
WL DEVICES
TEST ALL DEVICES
5.9.2
SHOW ALL DEVICES
SHOW RF PROBLEMS
TEST ONE DEVICE
Contact sensors
Motion sensors
Repeaters
GSM/GPRS
5.9.3
SIM NUMBER TEST
1
Select IP RCVR#
IP#1
IP#2
5.9.4
BROADBAND MODULE
2
PLEASE WAIT…
Unit is OK
5.9.5
5.9.2 Testing Wireless Devices
The PowerMaster enable to test the wireless devices attached to the panel. You can test all devices, one device at a
time, display devices' status and review RF problems, in case of any.
07:DIAGNOSTICS
⋅ ⋅ ⋅
WL DEVICES
⋅ ⋅ ⋅
MENU you wish
1
SIM number test is not applicable for UL installations
2
Broadband is not applicable for UL installations
3
The name of the product is PowerLink3 IP Communicator
- PowerMaster-10/30 G2 1
- Version 17 1
- 1. INTRODUCTION 3
- Figure 3.2 –Phone Wiring 9
- 3.4 GSM Module Installation 10
- 3.5 PGM-5 Installation 11
- Figure 3.6a – Cable Wiring 12
- UL listed 13
- PGM: not to be enabled in UL 13
- Figure 3.7a - Power Cable 14
- Connection 14
- Figure 3.9 - Final Closure 16
- Figure 4.3a – Phone Wiring 18
- 4.6 GSM Module Installation 20
- 4.8 PGM-5 Installation 21
- Figure 4.9a –Expander Module 22
- Figure 4.9b – Zone 23
- and Siren Wiring 23
- 4.11 Battery Insertion 25
- Figure 4.13 26
- 5. PROGRAMMING 27
- [1] in Step 1 above) 28
- 5.2.2 Selecting options 28
- – Exiting the Installer Mode 29
- – Setting Installer Codes 29
- 5.4 Zones / Devices 30
- Part B - Configuration 31
- - Configuring New Devices 32
- 5.4.3 Deleting a Device 34
- 5.4.5 Replacing a Device 34
- – Replacing a Device 35
- – Changing Defaults 35
- 5.5 Control Panel 36
- 01:ENTRY DELAY1 37
- 02:ENTRY DELAY2 37
- VOICE REPORT 38
- SMS REPORT 38
- 09:ARMING KEY 39
- 21:SWINGER STOP 39
- 22:CROSS ZONING 39
- 38:CANCEL ALARM 41
- 39:ALARM RESET 41
- 40:ABORT FIRE T 41
- 43:PANEL SIREN 41
- 44:SIREN TIME 41
- 5.6 Communication 44
- PowerMaster String Editor 48
- Event Reporting Chart 51
- IMAGE FORWARD 52
- 1st e-mail 52
- 2nd e-mail 52
- 5.6.8 Broadband 54
- 5.7 PGM Output 55
- 5.8 Custom Names 56
- 5.8.2 Record Speech 57
- 5.8.3 Voice Box Mode 57
- 5.9.4 Testing the SIM Number 60
- 5.10 User Settings 61
- 5.11 Factory Default 61
- 5.12 Serial Number 61
- 5.13 Start UL/DL 62
- 5.14 Partitioning 62
- 5.15 Operation Mode 62
- 5.15.2 Select setting 63
- 5.15.3 BS8243 Setup 63
- 5.15.4 DD243 Setup 64
- 5.15.5 CP01 Setup 66
- 5.15.6 OTHERS Setup 67
- 6. PERIODIC TEST 68
- 7. MAINTENANCE 70
- 7.4 Fuse Replacement 72
- 7.6 Annual System Check 72
- 8. READING THE EVENT LOG 73
- APPENDIX A. Specifications 74
- A2. Wireless 75
- A3. Electrical 75
- A4. Communication 76
- A5. Physical Properties 77
- B2. Common Areas 78
- Assignments 79
- C2. Keyfob Transmitter List 80
- APPENDIX D. Event Codes 82
- Type Number Range 83
- APPENDIX E. Sabbath Mode 84
- F1. Getting Started 85
- F2. Specifications 85
- F3. Installation 86
- Hardware Installation 87
- Control Panel Configuration 89
- APPENDIX G. Glossary 90
- Compliance with 92
- Standards 92
- WARRANTY 93
- Initiating Alarms 95
- Preparing to Arm 95
- Zone Bypass Scheme 96
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic POWERMASTER-10
(27 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais