Visonic PowerMax10 Especificações descarregar pdf (Página 3)

DE5450 PowerMax Installation Instructions 3

Backup Battery (provides power for at least 4 hours)

Option 1 - 9V, six alkaline AA cells, 1.8 Ah

Option 2 - 7.2 V, six Nickel Cadmium rechargeable AA

cells, 650 mAh

Option 3 - 7.2 V Nickel-Metal rechargeable battery pack,

1300 mAh, supplied by Visonic – to use a non-Visonic

battery pack, its battery snap should have proper polarity!

In Europe: For rechargeable cells, use BYD Battery

Company Ltd. D-AA700A (1,2 V / 700 mAh).

Battery Test: Once every 24 hours, and once per hour

during AC power loss.

2.4 Communication

Built-in Modem: 300 baud, Bell 103 protocol

Data Transfer to Local Computer: Via RS232 serial port

Report Destinations: 2 central stations, 4 private tele-

phones, 1 pager

Reporting Format Options: SIA, Pulse 4/2 1900/1400 Hz,

Pulse 4/2 1800/2300 Hz, Contact ID

Pulse Rate: 10, 20, 33 and 40 pps - programmable

Message to Private Phones: Tone or voice

Message to Pager: PIN No

.

Alarm Type



Zone No.

2.5 Physical Properties

Operating Temp. Range: 32°F to 120°F (0°C to 49°C)

Storage Temp. Range: -4°F to 140°F (-20°C to 60°C)

Humidity: 85% relative humidity, @ 30°C (86°F)

Size: 9-13/16 x 7-1/2 x 1-3/4 in. (250 x 190 x 44 mm).

Weight: 2 pounds (905 g) less batteries

Color: Ivory and charcoal gray

3. INSTALLATION

3. INSTALLATION3. INSTALLATION

3. INSTALLATION

3.1 Unpacking the Equipment

Open the cardboard packing box and check whether all

items have been included. If you find out that an item is

missing, contact your vendor or dealer immediately.

3.2 Supplying Power to the Unit

Enrolling the transmitting devices’ ID codes in the Power-

Max memory will be easier if carried out before actual

installation, with all detectors and the control panel on a

work bench. It is therefore necessary to power up the

PowerMax temporarily from the external power trans-

former or from its backup battery (see figure 1).

Disregard any “trouble” indications pertaining to lack of

battery or lack of telephone line connection.

Insert 7.2V battery pack (optional) to the battery holder

(to use non-original battery pack, its battery snap should

have proper polarity), or insert 6 battery cells.

Set ba ttery typ e

jumpe r p o sition :

For alkaline (dry)

batteries, set jumper

in DRY p os ition.

Fo r re ch argeable

batteries set jumper

in CHRG position

(as shown).

BAT

Remove battery area

cove r (see figu re 2,

steps 1-3), remove screw

and remove battery lid.

Figure 1. Backup Battery Insertion

CAUTION! Verify that the jumper is at the

correct position for the actual battery cells

being installed.

3.3 Programming

It is recommended to plan ahead - use the tables in

appendices A and B at the end of this guide to register the

intended location of each detector, the holder and

assignment of each transmitter and the control plan for the

X-10 units.

Gather up all transmitters and detectors used in the

system and mark each one in accordance with your

deployment plan.

Program the system now as instructed in the

PowerMax programming Guide (Publication DE5450P).

3.4 Mounting

Mounting process is shown in figure 3.

3.5 Wiring

All terminals and connectors are accessible within the

opening at the back of the PowerMax. All screw terminal

blocks can be pulled out, wired appropriately and plugged

back in.

WARNING! When plugging terminals back

into place, be sure to align them carefully

with the pins on the PCB. Mis-aligned or

reverse insertion of terminals may damage

internal PowerMax circuits!

The telephone-type connectors are also easy to deal with,

because of their quick attach/detach capability.

0.5A

COM+

INT -

EXT -

TOP

WIRING

CHANNEL

BOTTOM

WIRING

CHANNEL

6-TERMINAL

TEL. LINE

SOCKET

4-TERMINAL SOCKET

FOR X-10

CONTROLLER

POWER IN &

SOUNDER OUT

TERMINALS

ZONE 30 INPUT

TERMINALS

SOUNDER

FUSE

REAR

OPENING

LATERAL

WIRING

CHANNEL

LATERAL

WIRING

CHANNEL

Figure 2. Sunken Wiring Area Layout

3.6 Connecting the AC Transformer

CAUTION! Do not plug the transformer into the AC

outlet before completing all other wiring.

A. U.S.A. only: Remove the center screw from the AC wall

outlet.

B. Plug the transformer directly in - the Power LED of the

control panel should illuminate.

C. U.S.A. only: Use the screw removed in Step A above

to secure the transformer to the AC outlet. Tighten the

screw well.

D. The distance of the transformer from the system should

not exceed 150 ft using 18 AWG conductors.

1 2 3 4 5 6 7 8 ... 11 12

Comentários a estes Manuais

Sem comentários

Visonic PowerMax10 Especificações Página 3

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Visonic PowerMax10